Utility Bench PLR-800 Print-Friendly

Utility Bench PLR-800

Features

>		The Back Pad is wedged shaped to provide plenty of back support for the lower back and narrow enough at the top not encumber the shoulder blades in the down position of the movement. The seamless upholstery will prevent fungus and bacteria from hiding in the seams.

>		The seat is wedged shaped for comfort and is located low enough to the floor to provide easy entrance and exit of the bench.

>		Custom made rubber feet with bolt down holes

>		ABS Seat protective dishes


>		Wheels for easy transport

>		Galvanized foot rest for stability during the exercise

Dimensions

Width - 27 inches
Length - 58 inches

Unit Weight: 78 lb

Warranty

Our limited lifetime warranty is the industry’s best with a worry-free pledge that reflects a 40-year commitment to excellence. All Raptor Machines are covered by the following warranty:

Frame and welds - Lifetime Warranty

Upholstery - 1 Year

Specifications

>		Adjustable positions on all machines to accommodate all users to ensure correct biomechanical function. Adjustments are made with Heavy Duty spring loaded colored pull-pin knobs.

>		Weight Stacks are adjusted with a tethered, magnetic selector pin that extends through the entire weight stack.

>		Cable system. Cables are 1/4" . thick 4800lb test military spec galvanized oil impregnated air craft cable finished with a tough nylon coating to 3/16" . thick.

>		Manual Tension adjusters on every machine for the cable adjustments.

>		Weight stack plates are solid steel machined precisely to with in a 1/4 oz of weight.

>		Weight stack is accessible from a seated position.

>		Weight stacks are enclosed in Full Length Shrouds

>		Weight system allows user to increase resistance by 5lb increments.

>		Instructional guide charts used to inform correct usage for each machine along with anatomical highlights to show which muscle groups are being worked.

>		Each machine is made with a lower starting weight stack and has counter-balanced arms when needed.

>		Heavy-duty 40 oz. commercial grade marine naugahyde upholstery which is 85% mildew resistant. High density closed cell foam reinforced by 3/4" thick plywood backing for stable support.

>		Exceeds all ASTM requirements.

>		Guide rods are 1” CCRO ANSI 1045, solid steel hard chrome-plated with tensile strength of 75,000psi.

>		Frames are constructed of High Stress 3/16" . ASTM A-500 grade B structural steel tubing (11 gauge). 2" x 4"., 2" x 3" . tubing. 2" x 3" . tubing is use on all uprights, 2" x 2" x 1/8" . ASTM A-500 grade B structural carbon steel tubing (11 gauge) is used on cross members and benches.

>		All welds are ground down and stress tested

>		3-stage pre-paint preparatory process that includes a state of the art wash system that paralyzes the material. Then the material is processed through a dryer. The material is then sent through a preheat stage before it has the magnetic paint powder applied. (optional colors)

>		Urethane foam grades are a minimal grading of HR-125 (density pcf of 2.60 plus/minus 0.10 and above in high-compression areas (HR-150 with a density pcf of 4.60 plus/minus 0.30).

>		Cams are computer designed and laser cut to exact shape to allow proper variable resistance throughout the exercises complete range of motion. All Cams are 1/4" thick solid steel. The cams are different for each machine to provide the correct movement for the exercise.

>		Shrouded pulley housing is 6" x 1/4" . thick solid steel.

>		Pulley Wheels are 4 1/2" and 6" solid fiberglass reinforced body with a 1/2" . cable groove. Oil dipped double sealed racer ball bearings with a 1/2" axis shaft hole. Sealed for moisture and dust proof.